diff options
Diffstat (limited to 'sys-boot/raspberrypi-firmware/files')
-rw-r--r-- | sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-cmdline.txt | 1 | ||||
-rw-r--r-- | sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-config.txt | 65 |
2 files changed, 66 insertions, 0 deletions
diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-cmdline.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-cmdline.txt new file mode 100644 index 000000000000..b815bd89db1f --- /dev/null +++ b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-cmdline.txt @@ -0,0 +1 @@ +console=serial0,115200 console=tty1 root=ROOTDEV rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-config.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-config.txt new file mode 100644 index 000000000000..548f4accc250 --- /dev/null +++ b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-1.20201022-config.txt @@ -0,0 +1,65 @@ +# For more options and information see +# http://rpf.io/configtxt +# Some settings may impact device functionality. See link above for details + +# uncomment if you get no picture on HDMI for a default "safe" mode +#hdmi_safe=1 + +# uncomment this if your display has a black border of unused pixels visible +# and your display can output without overscan +#disable_overscan=1 + +# uncomment the following to adjust overscan. Use positive numbers if console +# goes off screen, and negative if there is too much border +#overscan_left=16 +#overscan_right=16 +#overscan_top=16 +#overscan_bottom=16 + +# uncomment to force a console size. By default it will be display's size minus +# overscan. +#framebuffer_width=1280 +#framebuffer_height=720 + +# uncomment if hdmi display is not detected and composite is being output +#hdmi_force_hotplug=1 + +# uncomment to force a specific HDMI mode (this will force VGA) +#hdmi_group=1 +#hdmi_mode=1 + +# uncomment to force a HDMI mode rather than DVI. This can make audio work in +# DMT (computer monitor) modes +#hdmi_drive=2 + +# uncomment to increase signal to HDMI, if you have interference, blanking, or +# no display +#config_hdmi_boost=4 + +# uncomment for composite PAL +#sdtv_mode=2 + +#uncomment to overclock the arm. 700 MHz is the default. +#arm_freq=800 + +# Uncomment some or all of these to enable the optional hardware interfaces +#dtparam=i2c_arm=on +#dtparam=i2s=on +#dtparam=spi=on + +# Uncomment this to enable infrared communication. +#dtoverlay=gpio-ir,gpio_pin=17 +#dtoverlay=gpio-ir-tx,gpio_pin=18 + +# Additional overlays and parameters are documented /boot/overlays/README + +# Enable audio (loads snd_bcm2835) +dtparam=audio=on + +[pi4] +# Enable DRM VC4 V3D driver on top of the dispmanx display stack +dtoverlay=vc4-fkms-v3d +max_framebuffers=2 + +[all] +#dtoverlay=vc4-fkms-v3d |