reinit the tree, so we can have metadata

7 files changed, 454 insertions, 0 deletions

diff --git a/sys-power/apcupsd/files/apcupsd-3.14.9-aliasing.patch b/sys-power/apcupsd/files/apcupsd-3.14.9-aliasing.patch
new file mode 100644
index 000000000000..09d9883a22f2
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd-3.14.9-aliasing.patch
@@ -0,0 +1,39 @@
+Index: apcupsd-3.14.9/src/apctest.c
+===================================================================
+--- apcupsd-3.14.9.orig/src/apctest.c
++++ apcupsd-3.14.9/src/apctest.c
+@@ -2206,18 +2206,18 @@ static struct {
+    const char *config_directive;
+    const char *descript;
+    char type;
+-   int *data;
++   void *data;
+ } cmd_table[] = {
+    {'u', "HITRANSFER",   "Upper transfer voltage",  'i', &eeprom_ups.hitrans},
+    {'l', "LOTRANSFER",   "Lower transfer voltage",  'i', &eeprom_ups.lotrans},
+    {'e', "RETURNCHARGE", "Return threshold",        'i', &eeprom_ups.rtnpct},
+    {'o', "OUTPUTVOLTS",  "Output voltage on batts", 'i', &eeprom_ups.NomOutputVoltage},
+-   {'s', "SENSITIVITY",  "Sensitivity",             'c', (int *)eeprom_ups.sensitivity},
++   {'s', "SENSITIVITY",  "Sensitivity",             'c', eeprom_ups.sensitivity},
+    {'q', "LOWBATT",      "Low battery warning",     'i', &eeprom_ups.dlowbatt},
+    {'p', "SLEEP",        "Shutdown grace delay",    'i', &eeprom_ups.dshutd},
+-   {'k', "BEEPSTATE",    "Alarm delay",             'c', (int *)eeprom_ups.beepstate},
++   {'k', "BEEPSTATE",    "Alarm delay",             'c', eeprom_ups.beepstate},
+    {'r', "WAKEUP",       "Wakeup delay",            'i', &eeprom_ups.dwake},
+-   {'E', "SELFTEST",     "Self test interval",      'c', (int *)eeprom_ups.selftest},
++   {'E', "SELFTEST",     "Self test interval",      'c', eeprom_ups.selftest},
+    {0,   NULL,           NULL}     /* Last entry */
+ };
+ 
+@@ -2240,9 +2240,9 @@ static void print_valid_eeprom_values(UP
+       for (j = 0; cmd_table[j].cmd; j++) {
+          if (cmd[i].cmd == cmd_table[j].cmd) {
+             if (cmd_table[j].type == 'c')
+-               asnprintf(val, sizeof(val), "%s", (char *)cmd_table[j].data);
++               asnprintf(val, sizeof(val), "%s", cmd_table[j].data);
+             else
+-               asnprintf(val, sizeof(val), "%d", *cmd_table[j].data);
++               asnprintf(val, sizeof(val), "%d", *((int*)cmd_table[j].data));
+ 
+             pmsg("%-24s %-12s  %-6s   ", cmd_table[j].descript,
+                cmd_table[j].config_directive, val);
diff --git a/sys-power/apcupsd/files/apcupsd-tmpfiles.conf b/sys-power/apcupsd/files/apcupsd-tmpfiles.conf
new file mode 100644
index 000000000000..601b5aeab5ef
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd-tmpfiles.conf
@@ -0,0 +1,3 @@
+D /run/apcupsd 0755 root root
+r /etc/apcupsd/powerfail
+r /etc/nologin
diff --git a/sys-power/apcupsd/files/apcupsd-udev.rules b/sys-power/apcupsd/files/apcupsd-udev.rules
new file mode 100644
index 000000000000..b2eeb27302d8
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd-udev.rules
@@ -0,0 +1,10 @@
+# do not edit this file, it will be overwritten on update
+
+ACTION!="add", GOTO="apcupsd_end"
+SUBSYSTEM!="usb", GOTO="apcupsd_end"
+ENV{ID_VENDOR}=="", IMPORT{program}="usb_id --export %p"
+ENV{ID_VENDOR_ID}!="051d", GOTO="apcupsd_end"
+
+KERNEL=="?*", SYMLINK+="apcups/by-id/$env{ID_BUS}-$env{ID_SERIAL_SHORT}"
+
+LABEL="apcupsd_end"
diff --git a/sys-power/apcupsd/files/apcupsd.conf b/sys-power/apcupsd/files/apcupsd.conf
new file mode 100644
index 000000000000..83201f3c2b14
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd.conf
@@ -0,0 +1,329 @@
+## apcupsd.conf v1.1 ##
+# 
+#  for apcupsd release 3.14.10 (13 September 2011) - gentoo
+#
+# "apcupsd" POSIX config file
+
+#
+# ========= General configuration parameters ============
+#
+
+# UPSNAME xxx
+#   Use this to give your UPS a name in log files and such. This
+#   is particulary useful if you have multiple UPSes. This does not
+#   set the EEPROM. It should be 8 characters or less.
+#UPSNAME
+
+# UPSCABLE <cable>
+#   Defines the type of cable connecting the UPS to your computer.
+#
+#   Possible generic choices for <cable> are:
+#     simple, smart, ether, usb
+#
+#   Or a specific cable model number may be used:
+#     940-0119A, 940-0127A, 940-0128A, 940-0020B,
+#     940-0020C, 940-0023A, 940-0024B, 940-0024C,
+#     940-1524C, 940-0024G, 940-0095A, 940-0095B,
+#     940-0095C, M-04-02-2000
+#
+UPSCABLE usb
+
+# To get apcupsd to work, in addition to defining the cable
+# above, you must also define a UPSTYPE, which corresponds to
+# the type of UPS you have (see the Description for more details).
+# You must also specify a DEVICE, sometimes referred to as a port.
+# For USB UPSes, please leave the DEVICE directive blank. For
+# other UPS types, you must specify an appropriate port or address.
+#
+# UPSTYPE   DEVICE           Description
+# apcsmart  /dev/tty**       Newer serial character device, appropriate for 
+#                            SmartUPS models using a serial cable (not USB).
+#
+# usb       <BLANK>          Most new UPSes are USB. A blank DEVICE
+#                            setting enables autodetection, which is
+#                            the best choice for most installations.
+#
+# net       hostname:port    Network link to a master apcupsd through apcupsd's 
+#                            Network Information Server. This is used if the
+#                            UPS powering your computer is connected to a 
+#                            different computer for monitoring.
+#
+# snmp      hostname:port:vendor:community
+#                            SNMP network link to an SNMP-enabled UPS device.
+#                            Hostname is the ip address or hostname of the UPS 
+#                            on the network. Vendor can be can be "APC" or 
+#                            "APC_NOTRAP". "APC_NOTRAP" will disable SNMP trap 
+#                            catching; you usually want "APC". Port is usually 
+#                            161. Community is usually "private".
+#
+# netsnmp   hostname:port:vendor:community
+#                            OBSOLETE
+#                            Same as SNMP above but requires use of the 
+#                            net-snmp library. Unless you have a specific need
+#                            for this old driver, you should use 'snmp' instead.
+#
+# dumb      /dev/tty**       Old serial character device for use with 
+#                            simple-signaling UPSes.
+#
+# pcnet     ipaddr:username:passphrase:port
+#                            PowerChute Network Shutdown protocol which can be 
+#                            used as an alternative to SNMP with the AP9617 
+#                            family of smart slot cards. ipaddr is the IP 
+#                            address of the UPS management card. username and 
+#                            passphrase are the credentials for which the card 
+#                            has been configured. port is the port number on 
+#                            which to listen for messages from the UPS, normally 
+#                            3052. If this parameter is empty or missing, the 
+#                            default of 3052 will be used.
+#
+UPSTYPE usb
+DEVICE 
+
+# POLLTIME <int>
+#   Interval (in seconds) at which apcupsd polls the UPS for status. This
+#   setting applies both to directly-attached UPSes (UPSTYPE apcsmart, usb, 
+#   dumb) and networked UPSes (UPSTYPE net, snmp). Lowering this setting
+#   will improve apcupsd's responsiveness to certain events at the cost of
+#   higher CPU utilization. The default of 60 is appropriate for most
+#   situations.
+POLLTIME 30
+
+# LOCKFILE <path to lockfile>
+#   Path for device lock file. Not used on Win32.
+LOCKFILE /run/apcupsd
+
+# SCRIPTDIR <path to script directory>
+#   Directory in which apccontrol and event scripts are located.
+SCRIPTDIR /etc/apcupsd
+
+# PWRFAILDIR <path to powerfail directory>
+#   Directory in which to write the powerfail flag file. This file
+#   is created when apcupsd initiates a system shutdown and is
+#   checked in the OS halt scripts to determine if a killpower
+#   (turning off UPS output power) is required.
+PWRFAILDIR /etc/apcupsd
+
+# NOLOGINDIR <path to nologin directory>
+#   Directory in which to write the nologin file. The existence
+#   of this flag file tells the OS to disallow new logins.
+NOLOGINDIR /etc
+
+
+#
+# ======== Configuration parameters used during power failures ==========
+#
+
+# The ONBATTERYDELAY is the time in seconds from when a power failure
+#   is detected until we react to it with an onbattery event.
+#
+#   This means that, apccontrol will be called with the powerout argument
+#   immediately when a power failure is detected.  However, the
+#   onbattery argument is passed to apccontrol only after the 
+#   ONBATTERYDELAY time.  If you don't want to be annoyed by short
+#   powerfailures, make sure that apccontrol powerout does nothing
+#   i.e. comment out the wall.
+ONBATTERYDELAY 10 
+
+# 
+# Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so
+# the first that occurs will cause the initation of a shutdown.
+#
+
+# If during a power failure, the remaining battery percentage
+# (as reported by the UPS) is below or equal to BATTERYLEVEL, 
+# apcupsd will initiate a system shutdown.
+BATTERYLEVEL 0 
+
+# If during a power failure, the remaining runtime in minutes 
+# (as calculated internally by the UPS) is below or equal to MINUTES,
+# apcupsd, will initiate a system shutdown.
+MINUTES 0 
+
+# If during a power failure, the UPS has run on batteries for TIMEOUT
+# many seconds or longer, apcupsd will initiate a system shutdown.
+# A value of 0 disables this timer.
+#
+#  Note, if you have a Smart UPS, you will most likely want to disable
+#    this timer by setting it to zero. That way, you UPS will continue
+#    on batteries until either the % charge remaing drops to or below BATTERYLEVEL,
+#    or the remaining battery runtime drops to or below MINUTES.  Of course,
+#    if you are testing, setting this to 60 causes a quick system shutdown
+#    if you pull the power plug.   
+#  If you have an older dumb UPS, you will want to set this to less than
+#    the time you know you can run on batteries.
+TIMEOUT 0
+
+#  Time in seconds between annoying users to signoff prior to
+#  system shutdown. 0 disables.
+ANNOY 45 
+
+# Initial delay after power failure before warning users to get
+# off the system.
+ANNOYDELAY 90 
+
+# The condition which determines when users are prevented from
+# logging in during a power failure.
+# NOLOGON <string> [ disable | timeout | percent | minutes | always ]
+NOLOGON disable
+
+# If KILLDELAY is non-zero, apcupsd will continue running after a
+# shutdown has been requested, and after the specified time in
+# seconds attempt to kill the power. This is for use on systems
+# where apcupsd cannot regain control after a shutdown.
+# KILLDELAY <seconds>  0 disables
+KILLDELAY 0
+
+#
+# ==== Configuration statements for Network Information Server ====
+#
+
+# NETSERVER [ on | off ] on enables, off disables the network
+#  information server. If netstatus is on, a network information
+#  server process will be started for serving the STATUS and
+#  EVENT data over the network (used by CGI programs).
+NETSERVER on 
+
+# NISIP <dotted notation ip address>
+#  IP address on which NIS server will listen for incoming connections.
+#  This is useful if your server is multi-homed (has more than one
+#  network interface and IP address). Default value is 0.0.0.0 which
+#  means any incoming request will be serviced. Alternatively, you can
+#  configure this setting to any specific IP address of your server and 
+#  NIS will listen for connections only on that interface. Use the
+#  loopback address (127.0.0.1) to accept connections only from the
+#  local machine.
+NISIP 127.0.0.1 
+
+# NISPORT <port> default is 3551 as registered with the IANA
+#  port to use for sending STATUS and EVENTS data over the network.
+#  It is not used unless NETSERVER is on. If you change this port,
+#  you will need to change the corresponding value in the cgi directory
+#  and rebuild the cgi programs.
+NISPORT 3551
+
+# If you want the last few EVENTS to be available over the network
+# by the network information server, you must define an EVENTSFILE.
+EVENTSFILE /var/log/apcupsd.events
+
+# EVENTSFILEMAX <kilobytes>
+#  By default, the size of the EVENTSFILE will be not be allowed to exceed
+#  10 kilobytes.  When the file grows beyond this limit, older EVENTS will
+#  be removed from the beginning of the file (first in first out).  The
+#  parameter EVENTSFILEMAX can be set to a different kilobyte value, or set
+#  to zero to allow the EVENTSFILE to grow without limit.
+EVENTSFILEMAX 25 
+
+#
+# ========== Configuration statements used if sharing =============
+#            a UPS with more than one machine
+
+#
+# Remaining items are for ShareUPS (APC expansion card) ONLY
+#
+
+# UPSCLASS [ standalone | shareslave | sharemaster ]
+#   Normally standalone unless you share a UPS using an APC ShareUPS
+#   card.
+UPSCLASS standalone
+
+# UPSMODE [ disable | share ]
+#   Normally disable unless you share a UPS using an APC ShareUPS card.
+UPSMODE disable
+
+#
+# ===== Configuration statements to control apcupsd system logging ========
+#
+
+# Time interval in seconds between writing the STATUS file; 0 disables
+STATTIME 0
+
+# Location of STATUS file (written to only if STATTIME is non-zero)
+STATFILE /var/log/apcupsd.status
+
+# LOGSTATS [ on | off ] on enables, off disables
+# Note! This generates a lot of output, so if         
+#       you turn this on, be sure that the
+#       file defined in syslog.conf for LOG_NOTICE is a named pipe.
+#  You probably do not want this on.
+LOGSTATS off
+
+# Time interval in seconds between writing the DATA records to
+#   the log file. 0 disables.
+DATATIME 0
+
+# FACILITY defines the logging facility (class) for logging to syslog. 
+#          If not specified, it defaults to "daemon". This is useful 
+#          if you want to separate the data logged by apcupsd from other
+#          programs.
+#FACILITY DAEMON
+
+#
+# ========== Configuration statements used in updating the UPS EPROM =========
+#
+
+#
+# These statements are used only by apctest when choosing "Set EEPROM with conf
+# file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD.
+#
+
+# UPS name, max 8 characters 
+#UPSNAME UPS_IDEN
+
+# Battery date - 8 characters
+#BATTDATE mm/dd/yy
+
+# Sensitivity to line voltage quality (H cause faster transfer to batteries)  
+# SENSITIVITY H M L        (default = H)
+#SENSITIVITY H
+
+# UPS delay after power return (seconds)
+# WAKEUP 000 060 180 300   (default = 0)
+#WAKEUP 60
+
+# UPS Grace period after request to power off (seconds)
+# SLEEP 020 180 300 600    (default = 20)
+#SLEEP 180
+
+# Low line voltage causing transfer to batteries
+# The permitted values depend on your model as defined by last letter 
+#  of FIRMWARE or APCMODEL. Some representative values are:
+#    D 106 103 100 097
+#    M 177 172 168 182
+#    A 092 090 088 086
+#    I 208 204 200 196     (default = 0 => not valid)
+#LOTRANSFER  208
+
+# High line voltage causing transfer to batteries
+# The permitted values depend on your model as defined by last letter 
+#  of FIRMWARE or APCMODEL. Some representative values are:
+#    D 127 130 133 136
+#    M 229 234 239 224
+#    A 108 110 112 114
+#    I 253 257 261 265     (default = 0 => not valid)
+#HITRANSFER 253
+
+# Battery charge needed to restore power
+# RETURNCHARGE 00 15 50 90 (default = 15)
+#RETURNCHARGE 15
+
+# Alarm delay 
+# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never
+# BEEPSTATE 0 T L N        (default = 0)
+#BEEPSTATE T
+
+# Low battery warning delay in minutes
+# LOWBATT 02 05 07 10      (default = 02)
+#LOWBATT 2
+
+# UPS Output voltage when running on batteries
+# The permitted values depend on your model as defined by last letter 
+#  of FIRMWARE or APCMODEL. Some representative values are:
+#    D 115
+#    M 208
+#    A 100
+#    I 230 240 220 225     (default = 0 => not valid)
+#OUTPUTVOLTS 230
+
+# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
+# SELFTEST 336 168 ON OFF  (default = 336)
+#SELFTEST 336
diff --git a/sys-power/apcupsd/files/apcupsd.init.4 b/sys-power/apcupsd/files/apcupsd.init.4
new file mode 100644
index 000000000000..ebd6b9755d4f
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd.init.4
@@ -0,0 +1,48 @@
+#!/sbin/openrc-run
+# Copyright 1999-2013 Gentoo Foundation
+# Distributed under the terms of the GNU General Public License v2
+
+INSTANCE="${SVCNAME#*.}"
+if [ -z "${INSTANCE}" ] || [ "${SVCNAME}" = "apcupsd" ]; then
+	INSTANCE="apcupsd"
+fi
+
+dir="/run/apcupsd"
+
+depend() {
+	use net
+}
+
+start_pre() {
+        checkpath -d -m 0775 -o root:uucp ${dir} 
+}
+
+start() {
+	rm -f /etc/apcupsd/powerfail
+
+	export SERVICE="${SVCNAME}"
+
+	if [ ! -d "${dir}" ]; then
+		einfo " Creating ${dir}"
+		/bin/mkdir -p "${dir}"
+		/bin/chown root:uucp "${dir}"
+	fi
+
+	ebegin "Starting APC UPS daemon"
+	start-stop-daemon \
+		--start --pidfile "${dir}/${SVCNAME}.pid" \
+		--exec /sbin/apcupsd -- \
+		-f "/etc/apcupsd/${INSTANCE}.conf" \
+		-P "${dir}/${SVCNAME}.pid"
+	eend $?
+}
+
+stop() {
+	ebegin "Stopping APC UPS daemon"
+	start-stop-daemon \
+		--stop --pidfile "${dir}/${SVCNAME}.pid" \
+            	--retry TERM/5/TERM/5 \
+		--exec /sbin/apcupsd
+	eend $?
+}
+
diff --git a/sys-power/apcupsd/files/apcupsd.powerfail.init b/sys-power/apcupsd/files/apcupsd.powerfail.init
new file mode 100644
index 000000000000..be591f86c185
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd.powerfail.init
@@ -0,0 +1,17 @@
+#!/sbin/openrc-run
+# Copyright 2009 Gentoo Foundation
+# Distributed under the terms of the GNU General Public License v2
+
+description='Signal the UPS to kill power in a power failure condition'
+
+depend() {
+	need mount-ro
+}
+
+start() {
+	if [ "$(runlevel | cut -d' ' -f2)" = "0" -a -f /etc/apcupsd/powerfail ] ; then
+		ebegin 'Signaling UPS to kill power'
+		/sbin/apcupsd --killpower
+		eend $?
+	fi
+}
diff --git a/sys-power/apcupsd/files/apcupsd.service b/sys-power/apcupsd/files/apcupsd.service
new file mode 100644
index 000000000000..9cec6e44194a
--- /dev/null
+++ b/sys-power/apcupsd/files/apcupsd.service
@@ -0,0 +1,8 @@
+[Unit]
+Description=APC UPS Monitor
+
+[Service]
+ExecStart=/sbin/apcupsd -b
+
+[Install]
+WantedBy=multi-user.target